Note: This article contains affiliate links. If you click on these links and make a purchase, I may earn a small commission at no extra cost to you. This helps support my research and content. Read my full affiliate disclosure here.
Choosing the right Nissan Murano valve cover gasket matters because a worn or failed seal can cause oil leaks, foul engine components, and lead to secondary issues over time. You want a gasket that fits precisely, resists oil and heat, and lasts through normal driving conditions. This guide highlights seven shortlisted valve cover gaskets selected for common Murano engines and explains the evaluation criteria used to pick them. Read on to understand the factors that affect longevity, sealing performance, and ease of replacement before you inspect your vehicle.
Looking for other parts? See all Nissan Murano parts & accessories.
Top Picks at a Glance
1. FRONEZER Engine Valve Cover Kit with Gasket, Bolts and Oil Filler Cap for 2016-2017 Nissan Murano 2.5L
| Fitment Engine | QR25DE, QR25DER 2.5L |
|---|---|
| Compatible Models | 2016-2017 Nissan Murano |
| Replaces Part Numbers | 13264-3KY0A, 132643KY0A, 13264-3TA0A |
This FRONEZER valve cover kit replaces the factory valve cover on Nissan Murano models equipped with the QR25DE/QR25DER 2.5L engine and is sold as a full replacement package. It arrives with the valve cover, valve cover gasket, spark plug tube seals, new bolts, a preinstalled PCV valve and a replacement oil filler cap so you do not need to source additional parts during installation. In practice the kit is used when a cracked or warped plastic cover or a failing gasket is causing oil leaks, low oil level warnings, or smell from the engine bay. Buyers report straightforward fitment and a tight seal that stops leaks when installed correctly. The practical benefits are reduced oil seepage, restored engine bay cleanliness, and the convenience of a single kit that covers all common failure points. Limitations are that fitment is strictly for the specified 2.5L Murano engine so ensure engine code compatibility, and installation still requires basic mechanical skill and torque control to avoid overtightening bolts and warping the cover.
Best for: A reliability-focused buyer who wants a factory-quality replacement to stop oil leaks and restore engine sealing on a 2016–2017 Nissan Murano with the 2.5L QR25DE/QR25DER engine.
Less Ideal for: Drivers who lack the tools or experience to perform valve cover replacement or who need a part for a different engine or model year should look elsewhere or consult a technician.
- Complete kit includes valve cover, gasket, spark plug tube seals, bolts, preinstalled PCV valve and oil filler cap so no additional parts are needed
- Made to replace the listed Nissan part numbers for direct fit on the QR25DE/QR25DER 2.5L engine used in Murano models
- Addresses common failure modes by restoring a tight seal and stopping oil leaks when installed properly
- Reports of consistent fit and durability from multiple buyers indicate reliable, repeatable replacement performance
- Compatible only with the specified 2.5L QR25DE/QR25DER engine and model years so it is not a universal fit
- Installation requires basic mechanical skill and correct torqueing of bolts to avoid cover warping
Verdict A full, reliability-focused valve cover replacement kit that restores a proper seal on 2016–2017 Nissan Murano 2.5L engines, provided you confirm engine compatibility.
2. JDMSPEED Valve Cover Set with Gaskets and Spark Plug Tube Seals for VQ35DE 3.5L (Pair)
| Engine fitment | VQ35DE V6 3.5L |
|---|---|
| Package contents | 2 valve covers, 2 gaskets, 6 spark plug tube seals |
| Compatible models | Altima, Maxima, Murano, I35, Quest (listed years) |
This JDMSPEED kit supplies both left and right valve covers plus the valve cover gaskets and six spark plug tube seals so you can replace leaking or warped covers on VQ35DE 3.5L engines. It is intended as a direct-fit replacement for affected Altima, Maxima, Murano, I35 and Quest model years listed, and arrives ready for installation without instructions. In practice this is a convenience-focused repair item: you get the pair of covers and seals in one purchase which avoids dealing with non-serviceable OEM tube seals and removes the need to source parts separately. Reported benefits include good fitment, a tight seal to stop oil leaks, and resistant construction that holds up under normal engine heat. Expect to need basic mechanical skill or a shop for correct installation since instructions are not included and some runners noted minor molding flash that must be cleared. Quality varies by unit and a minority of users reported premature leaking, so plan to inspect sealing surfaces and torque to spec during installation.
Best for: Buyers prioritizing convenience and a one-stop replacement solution who want to quickly fix oil leaks on a 3.5L VQ35DE engine without sourcing multiple parts separately.
Less Ideal for: Customers seeking a lifetime, premium OEM-equivalent part or those who prefer items with full installation guidance and guaranteed long-term warranties should consider other factory-quality options.
- Includes both left and right valve covers plus gaskets and all six spark plug tube seals for a complete repair
- Designed to be a direct replacement for VQ35DE 3.5L applications for straightforward fitment
- Construction resists warping and cracking to help maintain a lasting seal against oil leaks
- Saves time compared with sourcing individual parts or attempting to rebuild non-serviceable OEM covers
- No installation instructions included so novice installers may need professional help
- Some units show molding flash or minor defects that require trimming before installation
- A minority of users reported premature leakage, indicating inconsistent long-term durability
Verdict A convenient, all-in-one replacement valve cover kit for VQ35DE 3.5L engines that makes leak repairs faster but may require careful inspection and professional installation for best longevity.
3. Tykick Engine Valve Covers with Gasket for 3.5L V6 Nissan/Infiniti
| Brand | Tykick |
|---|---|
| Item model number | QMSG-9N00A |
| Replaces Part Number | 13264-9N00A, 13264-9N00B |
| Compatible engines | 3.5L V6 |
This Tykick kit supplies replacement valve covers with the gasket set to fit 3.5L V6 Nissan and Infiniti applications. It is used when original covers are cracked, leaking oil, or being replaced during engine work; installation involves removing the old covers, fitting the new gasket, and torquing to factory specs. The product advertises factory-spec fit and includes parts that cross-reference common Nissan part numbers for the 3.5L V6 family, which helps ensure correct alignment of bolt holes and PCV ports. Buyers will appreciate that the covers are a like-for-like replacement and come with a gasket to complete the job in one purchase. Limitations are that material and long-term durability details are not specified beyond a 6-month support window, and buyers should verify exact vehicle trim and engine code before ordering because compatibility lists cover many model years. Professional installation or adherence to torque procedures is recommended to avoid leaks.
Best for: Performance-oriented buyers who prioritize restoring engine sealing and appearance with a direct replacement part for the Nissan Murano 3.5L V6 and want parts that match factory fitment expectations.
Less Ideal for: Buyers looking for upgraded performance or long-term OEM warranties should consider higher-end or OEM-branded valve covers instead.
- Fits multiple 3.5L V6 Nissan and Infiniti models listed, simplifying parts selection
- Includes valve covers and gasket so the sealing surfaces are replaced together
- Manufactured to factory-spec fit which helps alignment with bolt patterns and ports
- Positive user feedback indicates straightforward fit and functioning on compatible vehicles
- Manufacturer only provides a 6-month support period for defects rather than a longer warranty
- Material composition and long-term longevity are not detailed in the listing
Verdict A practical, factory-fit replacement valve cover and gasket kit for 3.5L V6 Nissan/Infiniti engines that simplifies repairs but lacks extended warranty detail.
4. Quctaki Intake Manifold Gasket and Valve Cover Gasket Set for Nissan 3.5L V6
| Manufacturer | Yuechuan |
|---|---|
| Compatible engines | 3.5L V6 (Nissan/Infiniti) |
| Replaces part numbers | VS50770R, MS97143 |
This gasket set supplies both an intake manifold gasket and valve cover gaskets intended as direct replacements for Nissan 3.5L V6 engines. It is typically used during routine maintenance or when addressing oil leaks around the valve covers and intake manifold; installation requires removing the old gaskets and cleaning mating surfaces before fitting the new parts. The set claims compatibility with Murano and other Nissan/Infiniti models that use the 3.5L V6, and customer reports note an easy fit and straightforward assembly. For a budget option it delivers the basic sealing components needed to stop leaks and restore engine bay cleanliness. Limitations are the lack of detailed material specs and no explicit manufacturer warranty information, so long-term durability compared with factory-quality gaskets is uncertain. This kit is best for owners who need an affordable repair and are prepared to check torque and sealing during installation to ensure a proper fit.
Best for: Budget-conscious owners looking to stop oil leaks or replace worn gaskets on a Nissan Murano 3.5L V6 who prioritize affordability over long-term OEM assurance.
Less Ideal for: Drivers seeking a long-term factory-quality replacement backed by documented materials or extended warranty should consider higher-end or OEM-brand gaskets.
- Includes both intake manifold gasket and valve cover gaskets for a complete repair
- Listed compatibility with Nissan 3.5L V6 applications including Murano
- Multiple customer reports of good fit and easy installation
- Low-cost option compared with OEM replacements
- No detailed material or longevity specifications provided
- Manufacturer warranty and support details are not specified
Verdict A cost-effective gasket kit that fits Nissan 3.5L V6 applications like the Murano and is good for immediate leak repairs, but lacks detailed durability and warranty information.
5. PAROD Engine Valve Cover with Gasket for Nissan L4 2.5L
| Brand | PAROD |
|---|---|
| Item model number | PD13264JA00A |
| Replacement numbers | 13264JA00A, 13270-JA00A, 13264-JA00A, 13264-JG30C, 13270JA00A |
| Vehicle fitment note | Fits Nissan Altima, Rogue, Rogue Select, Sentra with 2.5L L4 per listing |
This PAROD kit replaces the valve cover and includes the gasket set designed for Nissan 2.5L L4 engines. It is installed in place of a worn or leaking factory valve cover to stop oil leaks around the head and restore a clean seal. The listing targets fitment for 2007–2013 Altima, 2008–2013 Rogue, 2014–2015 Rogue Select, and 2007–2012 Sentra using the 13264JA00A and related part numbers. Builders report the cover aligns with bolt holes and accepts existing hardware and the oil fill cap, which simplifies installation for a competent DIYer or an independent shop. The product is described as factory-quality aftermarket and the seller states the parts are tested. Practical benefits include replacing damaged covers that cause oil fouling of ignition coils and saving on labor compared with machining or repairing an old cover. Limitations: the cover may not include internal spark-plug tube seals for some model years and buyers should confirm exact year and engine variant before installing to avoid missing required components.
Best for: Risk-averse mainstream buyers who prioritize a tested, factory-quality replacement to stop oil leaks and restore a reliable engine bay seal with minimal surprises.
Less Ideal for: Drivers who prefer an exact OEM part source or who need parts that include every sub-seal for all year/trim permutations should look elsewhere or confirm required components first.
- Designed to match Nissan 2.5L L4 bolt pattern for direct replacement on listed models
- Includes gasket set so you replace the sealing surfaces at the same time
- Marketed as factory-quality aftermarket and 100% tested per the listing
- Multiple customers report good fit and resolution of oil leaks
- May not include internal spark-plug tube seals for certain model years which some installations require
- Fitment varies by year and trim so verification is required before purchase
Verdict A tested aftermarket valve cover and gasket kit aimed at stopping oil leaks on Nissan 2.5L L4 models, but confirm year-specific seal requirements before installing.
6. A-Premium Front & Rear Valve Cover Kit with Gaskets, Bolts and Oil Cap for Nissan 3.5L VQ35DE
| Position | Front, Rear |
|---|---|
| Material | Plastic |
| Valve Cover Gasket Included | Yes |
| Valve Cover Bolt Included | Yes |
| Oil Filler Cap Included | Yes |
This kit replaces both front and rear valve covers on Nissan V6 3.5L (VQ35DE) engines and comes with gaskets, bolts, a new oil filler cap and a PCV valve pre-installed where required. It is intended as a direct replacement to stop oil leaks that can foul coil packs and spark plugs and to restore proper crankcase ventilation. Typical use is a DIY or shop install when covers are cracked or gaskets have hardened; reviewers report good fitment and that the kit resolves common oil-leak symptoms. The covers are plastic and arrive pre-assembled with hardware so installation is straightforward once the intake is out of the way for the rear cover. Practical benefits include the complete parts set and lower cost compared with dealer parts. Limitations are that plastic covers are less heat-resistant than metal alternatives and long-term durability depends on installation torque and engine bay conditions, so expect to monitor the repair for leaks after fitting.
Best for: Practical optimizers who want a full, inexpensive repair kit that minimizes parts sourcing and lets them fix leak-prone Nissan 3.5L engines without paying dealer prices.
Less Ideal for: Buyers seeking maximum long-term durability under high-heat or performance use should consider higher-end metal or OEM-style replacements instead.
- Complete kit includes front and rear covers plus gaskets, bolts, oil filler cap and PCV valve where applicable
- Pre-assembled hardware speeds installation and reduces parts-sourcing hassle
- Direct-replacement fitment for Nissan 3.5L VQ35DE engines commonly resolves oil-leak symptoms
- Low cost compared with dealer or aftermarket individual components
- Plastic construction may not match the long-term heat and impact resistance of metal covers
- Rear cover installation can require intake removal on some vehicles, increasing labor time
Verdict A budget-friendly, all-in-one valve cover replacement kit that solves common oil-leak issues on Nissan 3.5L VQ35DE engines but uses plastic covers that may not match metal alternatives for extreme durability.
7. MITZONE Valve Cover Set with Gaskets, Bolts, Oil Cap and PCV Valve for Nissan 3.5L VQ35DE
| Brand | MITZONE |
|---|---|
| Position | Front |
| OEM Part Number | 13264-7Y010, 13264-8J102, 13264-7Y000, 13264-8J113, 264-984, 265-985 |
| Model | valve cover |
This MITZONE valve cover set replaces the front and rear covers on early VQ35DE 3.5L Nissan engines and ships with the key hardware needed for a straight swap. It is typically used to cure oil leaks, refresh deteriorated spark plug tube seals, and restore a clean sealing surface during an engine service. The kit includes both covers, valve cover gaskets, plug tube seals, bolts, an oil fill cap and a PCV valve which makes installation faster and avoids parts hunting. Buyers report generally good fitment to Murano and Maxima engines and that the covers are leak-resistant once properly installed. Important caveats are the supplied fasteners and finish quality; several users found screws prone to breakage under high torque and recommend care or upgraded hardware, and the painted exterior can chip if not handled carefully. Some experienced installers also note a small clearance area may require light modification for perfect fit on certain variants. For a balanced buyer wanting a complete, budget-friendly replacement, this kit delivers most of what you need but plan to inspect and possibly replace the fasteners during installation.
Best for: Buyers seeking a balanced, all-round repair solution who want a single kit that replaces both valve covers and all common sealing parts to fix oil leaks and simplify installation.
Less Ideal for: If you need factory-grade fasteners or a worry-free cosmetic finish without any chance of modification, consider sourcing upgraded hardware or a different premium cover set.
- Complete kit includes front and rear covers plus gaskets, plug tube seals, bolts, oil cap and PCV valve for one-stop replacement
- Designed for Nissan VQ35DE 3.5L engines so fitment and sealing surfaces match common 3.5L applications
- Many users report good leak control and straightforward installation when followed by careful prep and torqueing
- Some supplied bolts have broken for users when torqued to spec, so hardware quality is inconsistent
- Painted finish can chip or fade under high heat or rough handling, affecting appearance
- A small number of engines required minor grinding or adjustment for perfect clearance
Verdict A complete, budget-friendly valve cover replacement kit for early VQ35DE Nissan 3.5L engines that solves leaks and speeds installation but may require upgraded fasteners for long-term reliability.
Choosing the Right Nissan Murano Valve Cover Gasket: Key Factors to Consider
Material and Heat Resistance
The gasket material determines how well it withstands engine heat and exposure to oil over time. Materials such as multi-layer rubber composites or high-temperature silicone resist hardening and cracking, which preserves the seal and reduces the chance of leaks.
Material choice also affects compression set and ability to return to shape after repeated heat cycles. Choosing a gasket with proven resistance to oil and hydrocarbon exposure helps maintain the seal between service intervals and reduces the need for premature replacement.
Fitment Accuracy
Accurate fitment for the Nissan Murano valve cover is essential to create a uniform seal across the mating surfaces. A gasket that is too thick, thin, or misaligned can leave gaps or produce uneven compression, increasing the risk of a valve cover gasket leak.
Look for gaskets specified for the exact Murano engine and model year or those that provide clear compatibility information. Proper fitment reduces installation frustration and prevents stress on the gasket that can cause early failure.
Included Components and Completeness
Many valve cover gasket kits include additional parts such as grommets, washers, or sealant where needed. Having these components included ensures all wear points are addressed during replacement and reduces the chance of overlooking a failed piece that could compromise the seal.
Verify whether the kit contains valve cover bolt grommets and any required seals around oil passages. A complete kit simplifies the repair and helps achieve a consistent sealing surface when reinstalling the valve cover.
Durability and Longevity
Durability is influenced by material quality, resistance to heat and oil, and how the gasket copes with vibration and pressure changes. A longer-lasting gasket reduces maintenance frequency and the likelihood of oil leaks that can stain engine components or drip onto other parts.
Consider expected service life and whether the gasket maintains flexibility after many heat cycles. Durable gaskets often provide more reliable sealing throughout seasonal temperature variations and extended mileage.
Ease of Installation
Ease of installation matters because it affects whether you can complete a valve cover gasket replacement with common tools and reasonable time. Gaskets that are easy to position, hold their shape, and allow proper bolt torqueing reduce the risk of installation errors.
Clear instructions, good alignment features, and predictable behavior during reassembly make it more likely the job will be done correctly. This factor is especially important if you plan to perform the replacement yourself.
Sealing Behavior and Torque Tolerance
How a gasket reacts to bolt torque and clamping pressure affects long-term sealing. Some materials compress predictably and recover after torque cycles, while others may creep or harden, which can cause leaks later on.
Understanding valve cover gasket torque specs and using the correct tightening sequence helps ensure even compression. Choose a gasket with known torque tolerance characteristics to minimize the chance of leaks after installation.
FAQ
What are common valve cover gasket symptoms on a Nissan Murano?
Common signs include visible oil around the valve cover edges, burning oil smell from oil contacting hot engine parts, or oil pooling under the vehicle. You may also notice decreased engine bay cleanliness or contamination on nearby components. These symptoms often indicate the gasket is no longer sealing effectively.
How long does a valve cover gasket usually last?
Lifespan varies by material, driving conditions, and maintenance history, but valve cover gaskets often last many years under normal use. Exposure to extreme heat, frequent short trips, or chemical contamination can shorten life. Regular inspection will help you spot deterioration before major leakage occurs.
Can I replace the gasket myself and what should I watch for?
Many owners can handle a valve cover gasket replacement with basic tools and some mechanical aptitude. Important considerations include cleaning mating surfaces thoroughly, replacing any worn grommets, and following the correct bolt torque sequence. Take care not to overtighten bolts and ensure the gasket seats evenly to prevent new leaks.
Will a leaking valve cover gasket affect engine performance?
A leaking gasket usually does not immediately impact engine power, but it can create secondary issues over time. Oil leaks can foul ignition components, cause smoke when oil contacts hot parts, or lead to low oil levels if the leak is severe. Addressing leaks promptly reduces the risk of related problems.
How can I tell if the gasket or the valve cover is the problem?
Inspect the valve cover surface for warping, cracks, or damage when you remove the gasket. If the cover is damaged or warped, replacing the gasket alone may not stop leaks. Clean both surfaces and check for unevenness; a damaged valve cover often requires repair or replacement in addition to a new gasket.
Are there torque guidelines I should follow when reinstalling the valve cover?
Yes, following the manufacturer torque specs and tightening sequence is important to achieve even compression and prevent leaks. Tighten bolts progressively and in the recommended pattern, using a calibrated torque wrench when possible. If you are unsure of the exact values, consult a service manual for the correct specs.
How We Chose the Best Nissan Murano Valve Cover Gasket
We focused on features that directly affect sealing performance and long-term reliability for Nissan Murano valve cover gaskets. Key evaluation criteria included material composition and resistance to oil and heat, dimensional accuracy and fitment specifics for Murano engines, the completeness and quality of included seals or grommets, and documented durability or service life expectations. We also weighed ease of installation factors such as how the gasket behaves during reassembly and whether torque or sealing recommendations are well supported by technical guidance. We excluded parts with unclear fitment information, gaskets intended for non-Murano engines, and options that lacked basic material or dimensional specifications. Our selection prioritizes components that reduce the chance of leaking oil from valve cover areas and that support a straightforward valve cover gasket replacement process. Final choices reflect a balance of reliable sealing, appropriate materials, and practical installation considerations.
Our full evaluation process is outlined in our review methodology.
Conclusion
When choosing a Nissan Murano valve cover gasket, prioritize fitment accuracy, material resistance to oil and heat, and whether the kit includes all necessary seals and grommets. These factors have the biggest impact on preventing leaks and minimizing repeat work. Balance ease of installation and known torque behavior against durability expectations. Addressing any valve cover damage at the same time will increase the chance that the new gasket provides a lasting seal.
Explore More:
- Check out all Nissan Murano parts & accessories
- Explore Engine
- Browse all Auto Parts
